Signs on wallpapers
Below is the significance of the signs adopted explains the importance of symbols and quality marks, the wallpaper used.
Even before ordering wallpaper, it is important to know more important details about the article's alignment.
Corresponding to wallpapers is extremely important information to properly calculate the amount of wallpaper required.
In this article, we will look at all possible ways to match the wallpapers.
Without matching (Free Match, Random Match)
The easiest way to match the wallpaper with the following article, as each next sheet does not have to match the article. Most often, this type of matching occurs in monochrome and structured patterns. Some articles may have as many as two types of matching: both without coordination and with harmonization. In this case, we recommend opening at least two rolls and matching the article in both ways on the floor so you can understand what the result you like more before gluing.
Straight matching or Straight match
The beginning of a straight article with a reptort reference to centimeters (for example: 40/0); The same motifs are glued to each other at the same height.
With straight patterns, all sheets are glued at the same height by matching the article.
An article with a devotion or article alignment with a shift
This type of alignment is a bit more complicated as the article deviates between the strips. Information on this shift is indicated on the wallpaper label. In this way, the marking 64/32 cm meaning that the article recurs every 64 cm and the article is 32 cm between the left and the good wallpaper.
In the worst case, the scraps may be as large as the drawing raport (in this case, i.e. 32 cm).
If the room has niches, oblique walls or erkers, such details must be taken into account separately when calculating the amount of wallpaper.
Window and door areas are not deprived, but counted, as is the case for the calculation of the VOB painting work. The exact number of rolls required can only be clarified directly in the room or by using the project drawing.
A shifted drawing. The next strip pattern is shifted to the specified unit each time.
Wallpaper with a reverse pattern
Each other strip should be glued in reverse.
Reverse pattern for wallpapers is needed to provide a homogeneous parent between wallpaper sheets if the wallpaper patterns have a gradient or subtle shade. This bonding method will provide the look of the monolithic.
Reverse article. Glue in reverse. Each other strip should be glued in reverse.
Persistent at wet treatment. Insufficient dirt can be cleaned with a wet sponge.
Highly resistant to wet treatment. Dirt, except oils and fats, can be cleaned with soap solution and sponge if necessary.
Clean (resistant to rubbing). Resistant to rubbing, i.e. Dirt can be cleaned with soft soap liquid and soft rubbing.
Good lights persistent.
High -quality two -layer wallpapers (when gluing relief does not disappear)
In divided layers. The upper wallpaper layer can be removed dry. The lower layer of paper wallpaper remains on the wall.
Dry is completely removed. The wallpaper strip is released, which allows you to remove all strips in turn.
Kleister is applied to the wall trim in advance; wallpaper back part is pre -covered with a kleister, which is activated during temporary wetting.
Glue horizontally. The wallpaper column is glued not vertically but horizontally.
The glue is applied to the wall, which is covered with wallpaper (wall trim technique).
The glue is applied to the wall trim (for example: with a machine for gluing wallpaper).
Resistance to blows; It is characterized by special wallpapers with a particularly durable, firm-elastic surface.
Crossing and double neckline; Wallpaper stripes are applied 5-8 cm to each other and cut with a knife with a floating leg.
Removable wet condition means that the wallpaper is moistened during repair and then removed completely.
Matching material, i.e. These wallpapers are suitable for touching or cladding fabric.
"Ral-GZ 479". In order to meet the high quality and safety requirements, wallpaper manufacturers established an organization that controls quality. Without technical aspects, the quality mark of RAL first guarantees that the wallpapers manufactured do not endanger health and the environment.
Fire resistance. Until now, the fire resistance of the wall surfaces has been indicated by MPa Label according to DIN 4102. Since 2011, all manufactured wallpapers must be marked with CE according to EN 15102. The CE identification number EN 13501-1 indicates the appropriate resistance to fire class.
FSC-Label 4. The manufacturer of the FSC MIX marks the fact that the wallpaper used only wood of proven origin, or whether they were made of recycled raw materials. Such a sign shows a conscientious and responsible approach to forest resources.
